Applications
Funlam is  recommended for internal vertical applications and decorative or light duty horizontal surfaces. Consider the following application ideas:

Café & Restaurants
Clubs, Bars & Hotels
Feature walls, doors, panels
Decorative ceiling panels
Feature columns
Retail fit outs
Commercial fit outs
Reception desks
Lift Interiors
Signage
Exhibition stands
Set designs
Visual Merchandise
Laser emboss
Kitchen verticals & splash backs
Decorative horizontal features
Artworks

Benefits

Distinctive and unique
High visual impact
Is enhanced by light to give three dimensional qualities
Versatile, expressive, inspiring
Durable and flexible
Striking selection of colours and patterns
Special patterns can be supplied
Integrates beautifully with other textures and surfaces
Cost effective
Easy care
Simple installation
Environment friendly
Deal direct with manufacturer
Fast turnaround from receipt of order to despatch

Surface Protection

All Funlam sheets are supplied with a peel off film to protect the decorative finish. It is recommended that this film remain on the decorative surface until all processing and installation stages are complete.

Recommended Substrates

• • MDF, plywood, particle boards, decorative plastics.
  
• • For applications where moisture is a consideration, a substrate that is suitable for wet areas must be used.
  
• • Because Funlam is a decorative laminate, it is recommended that only high quality substrates should be used.
  

Surface Preparation

To maintain a high quality standard when utilizing Funlam , the surface that the sheeting is to be bonded to must be, relatively non-porous, very clean and free from oils and grease, evenly planed and free from defects and irregularities.

• Cutting
  
  • Good cutting results can be achieved with any of the following; panel saw, sharp carbide blades, guillotine, flat bed router.
    To deburr edges a fine file may be used.
  • All cutting and machinery must be done with the decorative surface of Funlam face up.
  

Bonding and Adhesives

• • Adhesives containing harmful solvents should not be used when bonding Funlam to a substrate.
• • Contact STEW Pty Ltd for information regarding recommended adhesives.
• • It is important that an even distribution of adhesive be applied to the underside of the sheet of Funlam. The adhesive must
    completely cover the entire underside surface of the sheet of Funlam to obtain successful lamination and to prevent any future   bubbling of the metal laminate.
• • Best and lasting results are obtained by using adhesives that are sprayed.
• • When bonding Funlam to substrates use a roller to allow for even and complete coverage. This will be achieved by maintaining
    a constant pressure throughout the rolling process, over the entire sheet.
• • Common causes of bonding failures are;
  1. 1. insufficient adhesive coverage to the laminate
  2. 2. insufficient pressure applied during the bonding process
  3. 3. incorrect surface preparation to the laminate
  4. 4. inferior quality substrate and incorrect type of substrate for the application
  5. 5. low temperature environments accompanied by high humidity
     
• • To obtain best results always follow adhesive manufacturer's instructions. Refer to the adhesive manufacturer for
    recommendations of a suitable solvent to remove excess glue.

Flexible Applications

• • Funlam is a flexible metal laminate which can be applied to curved surfaces and columns.
• • For tight tension joinery it is recommended to use strapping and clamps combined with fast tack contact adhesive.
• • If specifying Funlam for decorative ceiling panels, it is recommended that a greater sheet thickness than standard be used.
  

Fire Behaviour

Handling and Storage

• • Funlam sheets must be handled with care to prevent creasing of sheets.
• • Funlam sheets should be stored indoors and protected from moisture, dust and impurities.
• • Funlam sheets should be supported and stored vertically, off the ground with appropriate padding material at the base to protect
    edges.
  

Care

• • For cleaning Funlam the following can be used with a clean, soft cloth; warm soapy water, mild household detergent, diluted
    methylated spirits.
• • Do Not Use: Steel wool, scrapers, abrasive cleaning clothes, scouring liquids or powders to remove deposits as these   will permanently scratch the coating surface.
• • Note that detergents that recommend the use of gloves, should be avoided as this is a good indication that the detergent is harsh
    and therefore unsuitable for cleaning Funlam . For example do not use; thinners, acetone, solvents, caustics, chlorine liquid
    or any form of stripping agent.

Environment Friendly

• • Funlam is made from aluminium which can be melted down and recycled to be used for the production of new materials.
• • During the colour process no solvents are used and there are no emissions which means less waste and pollution to the
    environment.
• • All Funlam processes require low energy inputs which means they help preserve our energy resources.
  

Colours and Patterns

Due to the translucent nature of Funlam colours there maybe a slight variation from batch to batch. Funlam patterns are handcrafted artistic works, therefore each sheet may not be entirely uniform. It is recommended that an actual sample be obtained before specifying.Some variations in colours and patterns may occur when comparing the actual product to images viewed in printed brochure material and the website. The displayed colours and patterns are indicative only.

Lighting

Funlam is a light responsive laminate therefore its translucent colours, handcrafted patterns and three dimensional qualities are best enhanced by shining substantial and appropriate lighting onto its surface.When designing with Funlam consider quality lighting for example quartz halogen. Beam the light onto the Funlam surface from different angles for stunning illusionary effects which will bring a wow factor to any interior or application. Add life and an extra dimension to dark interiors with powerful Funlam colours, patterns and strategic light. Any mode and ambience can be created with selected Funlam colours and patterns and the right choice of lighting and lighting design.

Limitations

• • Funlam is recommended for internal vertical and decorative horizontal (light duty) use.
• • Funlam is not recommended for bench tops requiring heavy duty workloads.
• • Funlam is not recommended for applications where extensive heat temperatures are prevalent. When Funlam is used as a
     domestic splash back, ensure that an appropriate distance is maintained between the Funlam sheeting and oven or hot plate
     area. For further information contact the appliance manufacturer.
• • Funlam is not suitable in applications that have direct contact with salt water.